How to make a glitter tumbler with epoxy
When glittering tumblers, I recommend you put something on your surface to collect the falling glitter. I used freezer paper and a little plastic bowl Sprinkle your how to make a glitter tumbler with epoxy onto the tumbler on as evenly as you can. Note: The Mod Podge did not adhere the glitter to the tumbler very well in my experiment. There are sections with no glitter. And the tumbler made with Mod Podge required a second coat of glitter.
To use spray adhesive Loctite spray adhesive, not the Loctite spray adhesivebe sure you spray in a well-ventilated area not your craft room. When you spray your tumbler, use short bursts, just as Greg is doing in the video. Once you have spray adhesive on your tumbler, glitter again right away just as described earlier. Your goal is to get glitter evenly on the surface of the tumbler. Step 4: Seal the glitter on your tumblers with a clear coat. Seal your glitter with clear coat of sealer in a link area. Why do this? And when you put on your epoxy, you need to have things a bit more in control. Wait about 30 minutes after applying sealer to your glitter tumbler before moving on to the next step.
Step 5: Prepare a way to rotate your tumblers while they cure. While your sealer is drying on your glitter tumblers, get this part set up, or you can do it in advance, of course, because some of the ways are a little bit more complicated than others. There are two good methods of curing glitter tumblers.
The manual turning method is made with a cardboard box and PVC tubes. The cardboard method is a really inexpensive way, but you have to manually turn these, quite frequently in the beginning, to keep the epoxy from dripping down. So you need to have like several hours to sit and babysit your glitter tumblers when you do it this low-tech way. The power turning method involves building or buying a tumbler turner from a rotisserie turner, which I also did. We simply mounted a rotisserie turner to a board, and it turns the tumbler for you as you work. Between these two methods, I much prefer the motorized version, because it was easier to apply the epoxy.
How to Spray Paint a Tumbler
Step 6: Mix and apply high gloss resin to your glitter tumblers. You can brush off the extra solids or glitter that remain. This second set of tape should be applied in such a way that there's a slight area of stainless steel showing between the glitter and the tape, which is about to be covered by the epoxy. Step 2: Mixing and Applying Epoxy to the Glitter Tumbler Applying the epoxy is probably the most intimidating part of making glitter tumblers due to how technical it is.
First up, you have to set up the tumbler turner. You can make it with household items if you are creative enough, or you can ease the process by simply buying one. The good ones let how to make a glitter tumbler with epoxy adjust it as per the size of the tumbler. Use paper plates underneath to collect epoxy drips. Mixing Epoxy Mix the right this web page of epoxy- resin and hardener. Let the thinner part pour on to the thicker part slowly with a popsicle stick. Applying Epoxy Pour epoxy on the cup and turn it slowly. Smooth it across the cup as it rotates until you get all the epoxy on the cup, and the tumbler is covered with it. Spinning the Tumbler Once all the epoxy is on the cup, keep it spinning.
Wait about minutes, and carefully remove the https://ampeblumenau.com.br/wp-content/uploads/2020/02/archive/puzzle/can-you-cancel-amazon-prime-student-free-trial.php from both the top and bottom. Let the tumbler turner spin the tumbler slowly for hours. Take the tumbler off the turner and let it dry for as long as required, which could take several hours. Sanding grit sandpaper is most compatible with sand down the glitter tumbler.
This may make it look scratched up. Painters tape can also be used.
How to prep your tumbler The stainless tumblers need to be prepped a little before you start painting or adding glitter. Once you have taped your cup, give the exterior a light sanding with sandpaper all over the areas that are exposed. I recommend doing the light sanding by hand with sandpaper and not with a hand-sander. WHY you ask? Once you complete the sanding process, put a little dish soap on by hand and wash the cup to get off any dust. Dry your cup completely with a paper towel.
How to apply your paint I generally use flat spray paint to spray the exterior of my tumbler cups. Be careful not to apply too much paint or it will drip. If that happens, you may be able to cover with glitter. Otherwise, you might have to remove the paint and start all over. Using the Mod Podge method, paint a layer of Mod Podge on your entire tumbler. Place a piece of parchment or plain paper down on your surface.
Supplies for Making Glitter Tumblers with Epoxy
Liberally sprinkle glitter on the entire cup until completely coated. Mod Podge dries clear. Then all you have to do is paint another coat of Mod Podge on the entire cup and add another layer of glitter. Another easy way to glitter your cup is by spraying the outside with Loctite Spray Adhesive. If you use a spray adhesive, sprinkle glitter on liberally before the spray adhesive dries. Waste not, want not! How to properly mix and apply epoxy resin There are many brands of epoxy resin on the market. 
How to make a glitter tumbler with epoxy Video
Glitter Tumbler Tutorial for Beginners - Step by Step No Epoxy CrystaLac Method 2020How to make a glitter tumbler with epoxy - think
There are many different types out there, such as wood epoxy and Deep Pour Epoxy.There are two types of epoxy — art resin and table top — that are ideal for this type of project. Plus, each of these products cure to a crystal clear high-gloss finish. This will really help your glitter pop, making for a truly dazzling tumbler. Additionally, both are approved by the FDA as being percent food safe, and are crafted using the highest-quality ingredients. This is how you'll seal how to make a glitter tumbler with epoxy vinyl on the tumbler!
What level do Yokais evolve at? - Yo-kai Aradrama Message
Nelrajas